SAVE 35% OR MORE WITH A POWER-SAVE ENERGY SAVING KIT -
GUARANTEED!
Save 35% on Electric
Bills Or Your Money Back!
Buy and install any
Power-Save Energy Saving Kit. If after three months your year-over-year
electric bill is not 35% lower, Power-Save will give you a prompt refund
for 100% of the purchase price!
Power-Save Energy Saving
Kits are a cost-effective way to purchase a combination
of Power-Save products!
A Power-Save Energy Saving
Kit significantly reduces electric bills by eliminating wasted
electrical consumption and increasing the overall efficiency of the home.
In the event you decide to 'go solar' down the road,
the Power-Save Energy Saver Kit will allow you to install a much
smaller and less expensive solar system!
Power-Save Energy Saving Kits include:
1. The Power-Save 1200 Energy Saver
The Power-Save 1200™ is a small gray box that fits
neatly next to your breaker panel, saves you money year after year and
protects the entire home.
The Power-Save 1200™ was designed with the homeowner in mind,
providing lower energy bills, increased motor and appliance life,
for all of the equipment inside of your house.
Residential customers throughout North America could see a realized
savings of 8% - 10% typically and as much as 25% on their
electrical usage (and thus power bills). The Power-Save 1200™
is UL Certified as the Cat. No. ABET 2201 and CSA certified.
2. The Power-Save Solar Attic Fan
Saving energy in your home must start at the top. As warm air rises,
it collects in the attic making your entire house hotter and your air
conditioning less efficient. This costs you valuable dollars and
unnecessary wear and tear on your cooling equipment.
The
Power-Save Solar Attic fan removes hot air from the attic
keeping your home cooler while maximizing your air conditioner's
efficiency. The solar powered fan draws no electricity from
the utility and will cost you nothing to operate!
Removes Hot Attic Air; Solar Powered; Up to 850 CFM Air Flow; Optional
Thermostat; Same Day installation; Proudly Made in USA; 10/5/25 Year
Warranty; Saves Energy
Radiant barriers are installed in homes—most
commonly in attics—to reduce summer heat gain and winter heat
loss, which helps lower heating and cooling costs. The
barriers consist of a highly reflective material that reflects radiant
heat rather than absorbing it.
How Radiant Barriers
Work
Heat travels from a warm area to a
cool area by a combination of conduction, convection, and radiation.
Heat flows by conduction from a hotter material to a colder material
when the two materials touch. Heat transfer by convection occurs when
a liquid or gas is heated, becomes less dense, and rises. Radiant heat
travels in a straight line away from the hot surface and heats
anything solid as the wave of energy hits it.
When
the sun heats a roof, it's primarily the sun's radiant energy that makes
the roof hot. A large portion of this heat travels by conduction through
the roofing materials to the attic side of the roof. The hot roof material
then radiates its gained heat energy into the cooler attic (some of the
roof's heat will radiate in other directions too). A radiant barrier
reduces the radiant heat transfer from the roof to the attic space.
Fiberglass re-enforced (perforated) aluminum foil
insulation; Fire retardant; Reflects 95% of radiation heat Perforated
aluminum foil radiant barrier to eliminating sweating; Use for attics,
roof and walls ; Easily stapled into place in attic on ceiling joists or
rafters, sealed with aluminum tape; Adhesion Good on clean and dry
surface; No Discoloration Resistance Excellent resistance to water, water
vapor, oxidation and weathering.
4. Power-Save Duct Seal System
Duct sealing is a combination of Power-Save Radiant Barrier and
Power-Save Duct Seal.
Leaky ducts can reduce heating and cooling system efficiency
by as much as 20 percent. Sealing and insulating ducts
increases efficiency, lowers your energy bills, and can often pay for
itself in energy savings.
Plus, if you’re planning to install new heating and cooling equipment,
a well-designed and sealed duct system may allow you to
downsize to a smaller, less costly heating and cooling system
that will provide better dehumidification.
1)
tape all seams in duct work
2) wrap all duct work with radiant barrier
3) use same tape to attach radiant barrier to duct work and seal all
seams
